Configuring CloudBridge Connector between datacenter and AWS cloud
You can configure a CloudBridge Connector tunnel between a datacenter and AWS cloud to leverage the infrastructure and computing capabilities of the data center and the AWS cloud. With AWS, you can extend your network without initial capital investment or the cost of maintaining the extended network infrastructure. You can scale your infrastructure up or down, as required. For example, you can lease more server capabilities when the demand increases.
To connect a datacenter to AWS cloud, you set up a CloudBridge Connector tunnel between a Citrix ADC appliance that resides in the datacenter and a Citrix ADC virtual appliance (VPX) that resides in AWS cloud.
As an illustration of a CloudBridge Connector tunnel between a datacenter and Amazon AWS cloud, consider an example in which a CloudBridge Connector tunnel is set up between Citrix ADC appliance NS_Appliance-DC, in datacenter DC, and Citrix ADC virtual appliance (VPX) NS_VPX_Appliance-AWS.
Both NS_Appliance-DC and NS_VPX_Appliance-AWS function in L3 mode. They enable communication between private networks in datacenter DC and the AWS cloud. NS_Appliance-DC and NS_VPX_Appliance-AWS enable communication between client CL1 in datacenter DC and server S1 in the AWS cloud through the CloudBridge Connector tunnel. Client CL1 and server S1 are on different private networks.
Note:
AWS does not support L2 mode, hence it is necessary to have only L3 mode enabled on both the endpoints.
For proper communication between CL1 and S1, L3 mode is enabled on NS_Appliance-DC and NS_VPX_Appliance-AWS and routes are updated as such:
- CL1 have a route to NS_Appliance-DC for reaching S1.
- NS_Appliance-DC have a route to NS_VPX_Appliance-AWS for reaching S1.
- S1 should have a route to NS_VPX_Appliance-AWS for reaching CL1.
- NS_VPX_Appliance-AWS have a route to NS_Appliance-DC for reaching CL1.
The following table lists the settings on Citrix ADC appliance NS_Appliance-DC in datacenter DC.
Entity | 名字 | Details |
---|---|---|
The NSIP address | 66.165.176.12 | |
SNIP address | 66.165.176.15 | |
CloudBridge Connector tunnel | CC_Tunnel_DC-AWS | Local endpoint IP address of the CloudBridge Connector tunnel: 66.165.176.15, Remote endpoint IP address of the CloudBridge Connector tunnel: 168.63.252.133, GRE Tunnel Details - Name= CC_Tunnel_DC-AWS |
The following table lists the settings on Citrix ADC VPX NS_VPX_Appliance-AWS on AWS cloud.
Entity | 名字 | Details |
---|---|---|
NSIP address | 10.102.25.30 | |
Public EIP address mapped to the NSIP address | 168.63.252.131 | |
SNIP address | 10.102.29.30 | |
Public EIP address mapped to the SNIP address | 168.63.252.133 | |
CloudBridge Connector tunnel | CC_Tunnel_DC-AWS | Local endpoint IP address of the CloudBridge Connector tunnel:168.63.252.133, Remote endpoint IP address of the CloudBridge Connector tunnel: 66.165.176.15;GRE Tunnel Details名字= CC_Tunnel_DC-AWS, IPSec Profile Details, Name= CC_Tunnel_DC-AWS, Encryption algorithm= AES, Hash algorithm= HMAC SHA1 |
Prerequisites
Before setting up a CloudBridge Connector tunnel, verify that the following tasks have been completed:
Install, configure, and launch an instance of Citrix ADC Virtual appliance (VPX) on AWS cloud. For instructions on installing Citrix ADC VPX on AWS, seeDeploy a Citrix ADC VPX instance on AWS.
Deploy and configure a Citrix ADC physical appliance, or provisioning and configuring a Citrix ADC virtual appliance (VPX) on a virtualization platform in the datacenter.
Make sure that the CloudBridge Connector tunnel end-point IP addresses are accessible to each other.
Citrix ADC VPX license
After the initial instance launch, Citrix ADC VPX for AWS requires a license. If you are bringing your own license (BYOL), see the VPX Licensing Guide at:http://support.citrix.com/article/CTX122426.
You have to:
- Use the licensing portal within Citrix website to generate a valid license.
- Upload the license to the instance.
If this is apaidmarketplace instance, then you do not need to install a license. The correct feature set and performance will activate automatically.
Configuration steps
To set up a CloudBridge Connector tunnel between a Citrix ADC appliance that resides in a datacenter and a Citrix ADC virtual appliance (VPX) that resides on the AWS cloud, use the GUI of the Citrix ADC appliance.
When you use the GUI, the CloudBridge Connector tunnel configuration created on the Citrix ADC appliance, is automatically pushed to the other endpoint or peer (the Citrix ADC VPX on AWS) of the CloudBridge Connector tunnel. Therefore, you do not have to access the GUI (GUI) of the Citrix ADC VPX on AWS to create the corresponding CloudBridge Connector tunnel configuration on it.
The CloudBridge Connector tunnel configuration on both peers (the Citrix ADC appliance that resides in the datacenter and the Citrix ADC virtual appliance (VPX) that resides on the AWS cloud) consists of the following entities:
- IPSec profile—An IPSec profile entity specifies the IPSec protocol parameters, such as IKE version, encryption algorithm, hash algorithm, and PSK, to be used by the IPSec protocol in both the peers of the CloudBridge Connector tunnel.
- GRE tunnel—An IP tunnel specifies a local IP address (a public SNIP address configured on the local peer), remote IP address (a public SNIP address configured on the remote peer), protocol (GRE) used to set up the CloudBridge Connector tunnel, and an IPSec profile entity.
- Create a PBR rule and associate the IP tunnel with it—A PBR entity specifies a set of conditions and an IP tunnel entity. The source IP address range and the destination IP range are the conditions for the PBR entity. You must set the source IP address range and the destination IP address range to specify the subnet whose traffic is to traverse the CloudBridge Connector tunnel. For example, consider a request packet that originates from a client on the subnet in the datacenter and is destined to a server on the subnet in the AWS cloud. If this packet matches the source and destination IP address range of the PBR entity on the Citrix ADC appliance in the datacenter, it is sent across the CloudBridge Connector tunnel associated with the PBR entity.
To create an IPSEC profile by using the command line interface
At the command prompt, type:
添加ipsec配置文件<名称> [- * * ikeVersion * * (V1 | V2 )] [-**encAlgo** ( AES | 3DES ) ...] [-**hashAlgo**
...] [-**lifetime** ] (-**psk** | (-**publickey** -**privatekey** -**peerPublicKey** )) [-**livenessCheckInterval** ] [-**replayWindowSize** ] [-**ikeRetryInterval** ] [-**retransmissiontime** ] **show ipsec profile**
To create an IP tunnel and bind the IPSEC profile to it by using the command line interface
At the command prompt, type:
add ipTunnel
[-protocol ] [-ipsecProfileName ] show ipTunnel
To create a PBR rule and bind the IPSEC tunnel to it by using the command line interface
At the command prompt, type:
add ns pbr
ALLOW -srcIP = -destIP = -ipTunnel apply ns pbrs
show ns pbr
Example
> add ipsec profile CC_Tunnel_DC-AWS -encAlgo AES -hashAlgo HMAC_SHA1 Done > add ipTunnel CC_Tunnel_DC-AWS 168.63.252.133 255.255.255.0 66.165.176.15 –protocol GRE -ipsecProfileName CC_Tunnel_DC-AWS Done > add ns pbr PBR-DC-AWS ALLOW –srcIP 66.165.176.15 –destIP 168.63.252.133 ipTunnel CC_Tunnel_DC-AWS Done > apply ns pbrs Done
To configure a CloudBridge Connector tunnel in a Citrix ADC appliance by using the GUI
Type the NSIP address of a Citrix ADC appliance in the address line of a web browser.
Log on to the GUI of the Citrix ADC appliance by using your account credentials for the appliance.
Navigate toSystem>CloudBridge Connector.
In the right pane, underGetting Started, clickCreate/Monitor CloudBridge.
The first time you configure a CloudBridge Connector tunnel on the appliance, aWelcomescreen appears.
On theWelcomescreen clickGet Started.
Note:
If you already have a CloudBridge Connector tunnel configured on the Citrix ADC appliance, the Welcome screen does not appear, so you do not click Get Started.
- In theCloudBridge Connector Setuppane, clickamazon web services
- In theAmazonpane, provide your AWS account credentials: AWS Access Key ID and AWS Secret Access Key. You can obtain these access keys from the AWS GUI console. ClickContinue.
Note
Earlier, the Setup wizard always connects to the same AWS region even when another region is selected. As a result, configuring CloudBridge Connector tunnel to a Citrix ADC VPX running on the selected AWS region used to fail. This issue has been fixed now.
In theCitrix ADCpane, select the NSIP address of the Citrix ADC virtual appliance running on AWS. Then, provide your account credentials for the Citrix ADC virtual appliance. ClickContinue.
In theCloudBridge Connector Settingpane, set the following parameter:
- CloudBridge Connector Name—Name for the CloudBridge Connector configuration on the local appliance. Must begin with an ASCII alphabetic or underscore (_) character, and must contain only ASCII alphanumeric, underscore, hash (#), period (.), space, colon (:), at (@), equals (=), and hyphen (-) characters. Cannot be changed after the CloudBridge Connector configuration is created.
UnderLocal Setting, set the following parameter:
- Subnet IP—IP address of the local endpoint of the CloudBridge Connector tunnel. Must be a public IP address of type SNIP.
UnderRemote Setting, set the following parameter:
Subnet IP—IP address of the CloudBridge Connector tunnel end point on the AWS side. Must be an IP address of type SNIP on the Citrix ADC VPX instance on AWS.
NAT—Public IP address (EIP) in AWS that is mapped to the SNIP configured on the Citrix ADC VPX instance on AWS.
UnderPBR Setting, set the following parameters:
- Operation—Either the equals (=) or does not equal (!=) logical operator.
- Source IP Low—Lowest source IP address to match against the source IP address of an outgoing IPv4 packet.
- Source IP High—Highest source IP address to match against the source IP address of an outgoing IPv4 packet.
- Operation—Either the equals (=) or does not equal (!=) logical operator.
- Destination IP Low—Lowest destination IP address to match against the destination IP address of an outgoing IPv4 packet.
- Destination IP High—Highest destination IP address to match against the destination IP address of an outgoing IPv4 packet.
(Optional) UnderSecurity Settings, set the following IPSec protocol parameters for the CloudBridge Connector tunnel:
- Encryption Algorithm—Encryption algorithm to be used by the IPSec protocol in the CloudBridge tunnel.
- Hash Algorithm—Hash algorithm to be used by the IPSec protocol in the CloudBridge tunnel.
- Key— Select one of the following IPSec authentication methods to be used by the two peers to mutually authenticate.
- Auto Generate Key— Authentication based on a text string, called a pre-shared key (PSK), generated automatically by the local appliance. The PSKs keys of the peers are matched against each other for authentication.
- Specific Key—Authentication based on a manually entered PSK. The PSKs of the peers are matched against each other for authentication.
- Pre Shared Security Key—The text string entered for pre-shared key based authentication.
- Upload Certificates—Authentication based on digital certificates.
- Public Key—A local digital certificate to be used to authenticate the local peer to the remote peer before establishing IPSec security associations. The same certificate should be present and set for the Peer Public Key parameter in the peer.
- Private Key—Private key of the local digital certificate.
- Peer Public Key—Digital certificate of the peer. Used to authenticate the peer to the local end point before establishing IPSec security associations. The same certificate should be present and set for the Public key parameter in the peer.
ClickDone.
The new CloudBridge Connector tunnel configuration on the Citrix ADC appliance in the datacenter appears on the Home tab of the GUI. The corresponding new CloudBridge Connector tunnel configuration on the Citrix ADC VPX appliance in the AWS cloud appears on the GUI. The current status of the CloudBridge connector tunnel is indicated in the Configured CloudBridge pane. A green dot indicates that the tunnel is up. A red dot indicates that the tunnel is down.
Monitoring the CloudBridge Connector tunnel
You can monitor the performance of CloudBridge Connector tunnels on a Citrix ADC appliance by using CloudBridge Connector tunnel statistical counters. For more information about displaying CloudBridge Connector tunnel statistics on a Citrix ADC appliance, seeMonitoring CloudBridge Connector Tunnels.