IP Addressing

• Configuring Citrix ADC-owned IP addresses

  • 配置NSIP地址

  • Configuring and Managing Virtual IP (VIP) Addresses

  • Configuring ARP response Suppression for Virtual IP addresses (VIPs)

  • Configuring Subnet IP Addresses (SNIPs)

  • Configuring GSLB Site IP Addresses (GSLBIP)

  • Removing a Citrix ADC-owned IP address

  • Configuring Application Access Controls

• How the Citrix ADC Proxies Connections

• Enabling Use Source IP Mode

• Configuring Network Address Translation

  • Configuring INAT

  • Coexistence of INAT and Virtual Servers

  • Stateless NAT46 Translation

  • DNS64

  • Stateful NAT64 Translation

  • Configuring RNAT

  • Configuring Prefix-Based IPv6-IPv4 Translation

  • IP Prefix NAT

• Configuring Static ARP

• Setting the Timeout for Dynamic ARP Entries

• Configuring Neighbor Discovery

• Configuring IP Tunnels

• Class E IPv4 packets

Interfaces

• Configuring MAC-Based Forwarding

• Configuring Network Interfaces

• Configuring Forwarding Session Rules

• Understanding VLANs

• Configuring a VLAN

  • Configuring VLANs on a Single Subnet

  • Configuring VLANs on Multiple Subnets

  • Configuring Multiple Untagged VLANs across Multiple Subnets

  • Configuring Multiple VLANs with 802.1q Tagging

  • Associate an IP Subnet with a Citrix ADC Interface by using VLANs

  • Best practices for VLAN configurations

• Configuring NSVLAN

• Configuring Allowed VLAN List

• Configuring Bridge Groups

• Configuring Virtual MACs

• Configuring Link Aggregation

• Redundant Interface Set

• Binding an SNIP address to an Interface

• Monitoring the Bridge Table and Changing the Aging time

• Citrix ADC Appliances in Active-Active Mode Using VRRP

  • Configuring Active-Active Mode

  • Configuring Send to Master

  • Configuring VRRP Communication Intervals

  • Configuring Health Tracking based on Interface State

  • Delaying Preemption

  • Keeping a VIP Address in the Backup State

• Using the Network Visualizer

• Configuring Link Layer Discovery Protocol

• Jumbo Frames

  • Configuring Jumbo Frames Support on a Citrix ADC Appliance

  • Use Case 1 – Jumbo to Jumbo Setup

  • Use Case 2 – Non-Jumbo to Jumbo Setup

  • Use Case 3 – Coexistence of Jumbo and Non-Jumbo flows on the Same Set of Interfaces

• Citrix ADC Support for Microsoft Direct Access Deployment

Access Control Lists

• Simple ACLs and Simple ACL6s

• Extended ACLs and Extended ACL6s

• MAC地址为acl通配符掩码

• Blocking Traffic on Internal Ports

IP Routing

• Configuring Dynamic Routes

  • Configuring RIP

  • Configuring OSPF

  • Configuring BGP

  • Configuring IPv6 RIP

  • Configuring IPv6 OSPF

  • Configuring ISIS

  • Installing Routes to the Citrix ADC Routing Table

  • Advertisement of SNIP and VIP Routes to Selective Areas

  • Configuring Bidirectional Forwarding Detection

• Configuring Static Routes

• Route Health Injection Based on Virtual Server Settings

• Configuring Policy-Based Routes

  • Configuring a Policy-Based Routes (PBR) for IPv4 Traffic

  • Configuring a Policy-Based Routes (PBR6) for IPv6 Traffic

  • MAC Address Wildcard Mask for PBRs

  • Using NULL Policy Based Routes to Drop Outgoing Packets

• Traffic distribution in multiple routes based on five tuples information

• Troubleshooting Routing Issues

  • Generic Routing FAQs

  • Troubleshooting OSPF-Specific Issues

交通领域

• Inter Traffic Domain Entity Bindings

• Virtual MAC Based Traffic Domains