Stateful NAT64 Translation
The stateful NAT64 feature enables communication between IPv6 clients and IPv4 servers through IPv6 to IPv4 packet translation, and vice versa, while maintaining session information on the Citrix ADC appliance.
A stateful NAT64 configuration on the Citrix ADC appliance has the following components:
- NAT64 rule— An entry consisting of an ACL6 rule and a netprofile, which consists of a pool of Citrix ADC owned SNIP Addresses.
- NAT64 IPv6 Prefix— A global IPv6 prefix of length 96 bits (128-32=96) configured on the appliance. Note: Currently the Citrix ADC appliance supports only one prefix to be used commonly with all NAT 64 rules.
The Citrix ADC appliance considers an incoming IPv6 packet for NAT64 translation when all of the following conditions are met:
- The incoming IPv6 packet matches the ACL6 rule bound to a NAT64 rule.
- The destination IP address of the IPv6 packet matches the NAT64 IPv6 prefix.
When an IPv6 request packet received by the Citrix ADC appliance matches an ACL6 defined in a NAT64 rule and the destination IP of the packet matches the NAT64 IPv6 prefix, the Citrix ADC appliance considers the IPv6 packet for translation.
The appliance translates this IPv6 packet to an IPv4 packet with a source IP address matching one of the IP address bound to the netprofile defined in the NAT64 rule, and a destination IP address consisting of the last 32 bits of the destination IPv6 address of the IPv6 request packet. The Citrix ADC appliance creates a NAT64 session for this particular flow and forwards the packet to the IPv4 server. Subsequent responses from the IPv4 server and requests from the IPv6 client are translated accordingly by the appliance, on the basis of information in the particular NAT64 session.
Consider an example in which an enterprise hosts site www.example.com on server S1, which has an IPv4 address. To enable communication between IPv6 clients and IPv4 server S1, Citrix ADC appliance NS1 is deployed with a stateful NAT64 configuration that includes a NAT64 rule and a NAT64 prefix. A mapped IPv6 address of server S1 is formed by concatenating the NAT64 IPv6 prefix [96 bits] and the IPv4 source address [32 bits]. This mapped IPv6 address is then manually configured in the DNS servers. The IPv6 clients get the mapped IPv6 address from the DNS servers to communicate withIPv4 server S1.
The following table lists the settings used in this example:Stateful NAT64 translation example settings.
Following is the traffic flow in this example:
IPv6 client CL1 sends a request packet to Map-Sevr-IPv6 (2001:DB8:300::192.0.2.60) address.
The Citrix ADC appliance receives the request packet. If the request packet matches the ACL6 defined in the NAT64 rule, and the destination IP address of the packet matches the NAT64 IPv6 prefix, the Citrix ADC considers the IPv6 packet for translation.
The appliance creates a translated IPv4 request packet with:
- Destination IP address field containing the NAT64 prefix stripped from the destination address of the IPv6 request (Sevr_IPv4 = 192.0.2.60)
- Source IP address field containing one of the IPv4 address bound to Netprofile-1(in this case, 192.0.2.100)
The Citrix ADC appliance creates a NAT64 session for this flow and sends the translated IPv4 request to server S1.
IPv64 server S1 responds by sending an IPv4 packet to the Citrix ADC appliance with:
- Destination IP address field containing 192.0.2.100
- Source IP address field containing the address ofSevr_IPv4(192.0.2.60)
The appliance receives the IPv4 response packet, searches all the session entries, and finds that the IPv6 response packet matches the NAT64 session entry created in step 4. The appliance considers the IPv4 packet for translation.
The appliance creates a translated IPv6 response packet with:
- Destination IP address field=Client_IPv6=2001:DB8:5001::30
- Source IP address field = Concatenation of NAT64 Prefix (First 96 bits) and Sevr_IPv4 (last 32 bits) =2001:DB8:300::192.0.2.60
The appliance sends the translated IPv6 response to client CL1.
Limitations of Statelful NAT64
The following limitations apply to stateful NAT64:
- Translation of IPv4 options is not supported.
- Translation of IPv6 routing headers is not supported.
- Translation of hop-by-hop extension headers of IPv6 packets is not supported.
- Translation of ESP and EH headers of IPv6 packets is not supported.
- Translation of multicast packets is not supported.
- Packets of Stream Control Transmission Protocol (SCTP), Datagram Congestion Control Protocol (DCCP), and IPSec, are not translated.
Configuring Stateful NAT64
Creating the required entities for stateful NAT64 configuration on the Citrix ADC appliance involves the following procedures:
- Add an ACL6 rule with action ALLOW.
- Add an ipset, which binds multiple IP addresses.
- Add a netprofile and bind the ipset to it. If you want to bind only one IP address, you need not create an ipset entity. In that case, bind the IP address directly to the netprofile.
- Add a NAT64 rule, which includes binding the ACl6 rule and the netprofile to the NAT 64 rule.
- Add a NAT64 IPv6 prefix.
CLI procedures
To add an ACL6 rule by using the CLI:
At the command prompt, type:
- add ns acl6
…
To add an IPset and bind multiple IPs to it by using the CLI:
At the command prompt, type:
- add ipset
- bind ipset
To add a netprofile by using the CLI:
At the command prompt, type:
- 添加netprofile <名称> -srcIP < IPaddress或IPset >
To add a NAT64 rule by using the CLI:
At the command prompt, type:
- add nat64
-netProfile
To add a NAT64 prefix by using the CLI:
At the command prompt, type:
-
set ipv6 -natprefix *>
Example:
>添加acl6交流L6-1 ALLOW -srcIPv6 2001:DB8:5001::30 Done > apply acls6 Done > add ip 192.0.2.100 255.255.255.0 –type SNIP Done > add ip 192.0.2.102 255.255.255.0 –type SNIP Done > add ipset IPset-1 Done > bind ipset IPset-1 192.0.2.100 192.0.2.102 IPAddress "192.0.2.100" bound IPAddress "192.0.2.102" bound Done > add netprofile Netprofile-1 -srcIP IPset-1 Done > add nat64 NAT64-1 ACL6-1 -netprofile Netprofile-1 Done > set ipv6 -natprefix 2001:DB8:300::/96 Done
GUI procedures
To add a NAT64 rule by using the GUI:
Navigate to System > Network > Routes > NAT64, and a new NAT64 rule, or edit an existing rule.
To add a NAT64 prefix by using the GUI:
Navigate to System > Network, in the Settings group, click Configure INAT Parameters, and set the Prefix parameter.